STEEL NAVIGATOR Find the right steel for your needs

Filter datasheet

Variants

Last revised: Wed, 04 Dec 2024 16:18:12 GMT

9MnV5*

All

General Information

9MnV5* is also referred to as S355L4. It is a micro-alloyed steel for general purposes where fantastic impact properties at low temperatures as well as defined mechanical properties are demanded. It is especially suitable for this sections. It has a tight chemical composition as well as low levels of residual elements to give small variations in the mechanical properties. The low carbon equivalent CEV makes it suitable for welding.

* Designation followed by "*" is not an official EN standard grade but named according to the rules in EN 10027.

Similar designations

AH36, S355J2

Chemical composition

Variant	Cast	Weldability		C %	Si %	Mn %	P %	S %	Cr %	V %	Al %
S355L4	CC	CEV 0.4_max	Min	0.07	0.25	1.20	-	-	-	0.070	0.020
S355L4	CC	Pcm 0.2_max	Max	0.10	0.50	1.40	0.030	0.015	0.15	0.110	0.050

Mechanical Properties

Variant	Condition	Format	Dimension [mm]	Yield strength min [MPa]	Tensile strength [MPa]	Elongation A₅ [%]	Reduction of area Z_min [%]	Impact (ISO-V) strength_min
Rp_0.2 * R_eh, ** R_el
S355L4	+AR	All formats	5 < 16	355**	470-630	23	0	-40 °C 60 J (long)
		All formats	16.1 < 40	345**	470-630	22	-	-40 °C 60 J (long)
		All formats	40.1 < 63	335	470-630	21	-	-40 °C 60 J (long)
		All formats	63.1 < 80	325**	470-630	21	-	-40 °C 60 J (long)

Round bars start at 14 mm as minimum dimension. Maximum thickness for flat bar is 80 mm for widths 95-160 mm.

Transformation temperatures

	Temperature °C
MS	461
AC1	719
AC3	840

The grade is not intended for heat treatment operations. Normalizing is not necessary as normalised rolling is performed.

SUSTAINABILITY-ENVIRONMENTAL IMPACT DATA

At Ovako sustainability and reduction of our environmental impact is a major focus in everything we do.
Further information is found here.

Steel works	Hofors	Smedjebacken	Imatra
CO2e/kg	120	62	76

To get the full picture of our products environmental impact we have to look at all of our CO₂ emission sources.
Not only the steel work Scope 1-2 itself, but all operations downstream in our production, heating and heat treatment furnaces etc (full scope 1-2) as well as all the emission from input material, eg. alloys, scope 3.

Steel Grade	Format	Condition	Scope 1-3 (CO2e kg /1000 kg steel)	Climate compensated Net emission = Scope 3 (CO2e kg /1000 kg steel) Scope 1 - 2 = 0 (compensated)
S355L4	Flat bar	+AR	393	171

All above data are to be seen as typical values for the specified format and condition. Detailed information about your specific product please contact your sales contact.

Other properties (typical values)

Youngs module (GPa)	Poisson´s ratio (-)	Shear module (GPa)	Density (kg/m3)
210	0.3	80	7800
Average CTE 20-300°C (µm/m°K)	Specific heat capacity 50/100°C (J/kg°K)	Thermal conductivity Ambient temperature (W/m°K)	Electrical resistivityAmbient temperature (µΩm)
12	460 - 480	40 - 45	0.20 - 0.25

Contact us

Would you like to know more about our offers? Don´t hesitate to contact us:

Via e-mail: info@ovako.com

Via telephone: +46 8 622 1300

For more detailed information please visit http://www.ovako.com/en/Contact-Ovako/

Disclaimer

The information in this document is for illustrative purposes only. The data and examples are only general recommendations and not a warranty or a guarantee. The suitability of a product for a specific application can be confirmed only by Ovako once given the actual conditions.The purchaser of an Ovako product has the responsibility to ascertain and control the applicability of the products before using them. Continuous development may necessitate changes in technical data without notice. This document is only valid for Ovako material. Other material, covering the same international specifications, does not necessarily comply with the properties presented in this document.

General information
Chemical composition
Mechanical properties
Transformation temp.
Sustainability